Elements - AS270 Economical Acetic Cure Silicone Sealant

RI_SS_AS270_B
AED8000
Excl. VAT
In stock
Price in points: 80 points

Brand: Elements

ELEMENTS AS270 is a single component Acetic cure silicone sealant which vulcanizes on exposure to moisture in the air at room temperature, to produce a flexible elastomeric sealant. 

It is suitable for all common construction and glazing application. It is easy to apply and offers excellent adhesion to a variety of nonporous substrates such as glass, glazed ceramic tiles and aluminum. It is resistant to ozone, ultra-violet radiation and temperature extremes.

Easy – to – use one component type.

Antifungal to suit sanitary and wet area applications.

Cures at room temperature at ambient humidity conditions.

Outstanding adhesiveness to many non-porous substrates, including Glass, Glazed Ceramics, Aluminum, Masonry, some Plastics etc.

All temperature gun ability – can be applied in all temperatures. 

Excellent resistance to weathering, moisture, ozone, UV, temperature Extremes etc.

Type: 100% silicone 1 component

Appearance: Smooth, non-slump paste


Surface Preparation

All surfaces should be clean and dry and free of dust, dirt, and grease.

Priming is normally not required for applications to nonporous surfaces. Applying a small trial bead and allowing 7  days for maximum adhesion to occur can easily test unprimed adhesion. If primer is required contact manufacturer.


Application

ELEMENTS AS270 is ready-to-use requires no mixing or additives. The cure mechanism begins as soon as the sealant comes in contact with air. Higher humidity accelerates cure, and curing time is increased with the thickness of the sealant. 

In applications where partial or total confinement of sealant is prevalent, the time required for proper cure is generally lengthened by the degree of confinement.

Tooling, if necessary, should be done before “skinning” takes place.


Packing

ELEMENTS AS270 is available in standard caulking cartridges. Other sizes like sausage and tubes are available upon request.


Health and Safety

ELEMENTS AS270 releases small amounts of acetic acid during cure. Adequate ventilation should be provided with the extensive use of this sealant.

Keep Out of Reach of Children.


Storage and Shelf life

ELEMENTS AS270 cartridge should always be stored in dry and covered areas. The product should not be exposed to direct sunlight or be kept near any source of heat. Store in indoor at 25 C.

The product Shelf life is up to 12 months when stored as per the recommended storage conditions.


Warranty

ELEMENTS AS270 warrants that its products will meet its specifications. Royal Industries shall in no event be liable for incidental or consequential damages. 

Except as expressly stipulated, Royal Industries liability, expressed or implied, is limited to the stated selling price of any defective goods. 

Data is subject to change without notice and it is therefore recommended that this information not be used for specification writing. For additional information on specific applications, contact the manufacturer.


Temperature Range‡ 

Application:                                                                             Temperature Ambient to 50°C (120°F) 

Useable Temperature Range:                                                    -40°C to 110°C (-40°F to 230°F) 


Drying Time* 

Tack free time:                                                                         30 minutes 

Skin-Over Time:                                                                        10 minutes @ 25˚C (77˚F) 

Cure rate:                                                                                 3-4 mm/day 

Cure Time:                                                                                24-26 hours 

Full Physical Characteristics:                                                      7 days 


PHYSICAL PROPERTIES

(Typical properties - values not to be used as specifications).


Uncured 

Specific Gravity 0.94 ±2 gm/cm3 @ 25˚C Cure System Acetoxy, Moisture Cure. 


Cured at Standard Conditions* for 7 Days 

Tensile Strength (ASTM D412):                                                            ≤1.22 N/mm2 

Elongation at Break (ASTM D412):                                                       500%

 Modulus at 100% elongation [ASTM D412]:                                          ≤0.4N/ m2 

Movement accommodation factor:                                                      ≤ 20%

Possibly you may be interested
  • Most Popular
  • Bestsellers
  • Recently Viewed
 
 
 
Fast and high quality delivery

Our company makes delivery all over the country

Quality assurance and service

We offer only those goods, in which quality we are sure

Returns within 30 days

You have 30 days to test your purchase